Network
Flash, Intel, Tool
Source
Edit
History

Intel Ethernet Network Adapter Flash Tool eeupdate

Catalogue
  1. 1. eeupdate
    1. 1.1. MAC address
  2. 2. 参考资料

eeupdate

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192

Using: Intel (R) PRO Network Connections SDK v2.30.25
EEUPDATE v5.30.25.06 
Copyright (C) 1995 - 2017 Intel Corporation
Intel (R) Confidential and not for general distribution.
-----------------------------------------------------
Options:
    /HELP or /?
       Displays command line help.
    /EXITCODES
       Displays exit code help.
    /ALL
       Selects all adapters found in the system.
    /NIC=XX
       Selects a specific adapter (1-32).
    /BUS=XX
       Selects PCI bus of adapter to program. Must be used with the DEV
       parameter to specify an adapter.
    /DEV=XX
       Selects PCI device of the adapter to program. Must be used with the
       BUS parameter to specify an adapter.
    /FUN=XX
       Selects PCI function of the adapter to program. Must be used with both
       the BUS and DEV parameters to specify an adapter.
Press <Enter> to continue...
    /DEVICE=<pci device ID>
       4 hex digit device id of card to program.
    /SUBDEVICE=<pci subsystem device ID>
       4 hex digit subsystem device id of card to program.
    /DUMP
       Dumps EEPROM/Shadow RAM memory contents to        file *.eep and flash memory to *.bin (if available)
    /MAC_DUMP_FILE
       Dumps the MAC address to a file usable by the /A command.
    /MAC_DUMP
       Displays the adapter LAN MAC address.
    /MAC_DUMP_ALL
       Displays all the MAC addresses.
    /MAC_ALL_TO_FILE
       Dumps all the MAC addresses to a file usable by the /MAC_ALL_FROM_FILE
       command.
    /MAC_ALL_FROM_FILE <addrfile>
       Programs all MAC addresses from text file to a device.
       File should contain 13 MAC addresses (9 for PEPs and
       4 custom MAC addresses), one each line. EUI48 and EUI64 formats accepted.
    /CB <offset> <bitmask>
       Clears bits in the EEPROM, specified in <bitmask>.
    /SB <offset> <bitmask>
       Sets bits in the EEPROM, specified in <bitmask>.
Press <Enter> to continue...
    /RW <word>
       Reads <word> from the EEPROM.
    /WW <word> <value>
       Writes <value> into <word> in EEPROM.
    /MAC=macaddr [/NUM=PF_num]
       Programs the EEPROM/NVM with only the MAC address of
       macaddr without changing the rest of the EEPROM/NVM.
       /NUM is optional and I40E specific - it defines target PF.
    /A <addrfile> or /address <addrfile>
       Programs the EEPROM/NVM with only the MAC address from
       the <addrfile> without changing the rest of the
       EEPROM.
    /D <imagefile> or /DATA <imagefile>
       Programs the NVM [EEPROM/FLASH] with the contents of <imagefile>
       without changing the MAC address.
    /PHYNVM <imagefile>
       Programs the PHY NVM with the contents of <imagefile>

    /DEBUG
       Forces debug update to be used where applicable.
       Must be used with /D or /DATA switch.
    /CALCCHKSUM
       Forces the EEPROM checksum and CRCs to be updated.
Press <Enter> to continue...
    /EEPROMVER
       Displays the version of the EEPROM image.
    /INVMVERSION
       Displays the version of the iNVM image.
    /PCIINFO
       Displays the PCI information of the adapter.
    /ADAPTERINFO
       Displays additional information about the adapter, such as EtrackID,
       PF MAC address, or image and firmware version.
    /TEST
       Checks the EEPROM/NVM checksum(s) and size.
    /IDFLASH
       Displays the flash ID and its protected status.
    /VERSION
       Displays version and the diagnostic library information.
    /PHYID <imagefile>
       Programs the PHY ID NVM with the contents of <imagefile>.
    /PHYID_DUMP
       Dumps PHY ID NVM contents to a file with the name:       <PHY ID>_<PHY card version>.bin
    /PHYID_VERIFY <targetfile> 
       Verifies the PHY ID NVM image in eeprom against the file
       specified in <targetfile>.
Press <Enter> to continue...
    /FLASH_DUMP <targetfile> 
       Dumps contents of the whole flash memory of
       selected adapters to *.bin file

    /EEPROM_DUMP
       Dumps contents of the EEPROM/Shadow RAM memory of
       selected adapters to *.eep file
    /GUI
       Brings up GUI mode.
    /GUI /HELP
       Displays GUI help.
    /NOPROT
       When programming an image for devices that support NVM protection,
       prevents protection from being enabled. This switch must be used
       with the /DATA command and has no effect on NVM devices that are
       already protected.
    /DEBUGLOG <debugfile>
       Log debug messages into the debugfile.
    /VERIFY <targetfile>
       Verifies the eeprom/NVM image in eeprom/NVM to the target file
       specified in <targetfile>.
Press <Enter> to continue...
    /CHECKIMAGE
       Verifies that the NVM in <imagefile> can be loaded over the running NVM.
    /VERIFYPHYNVM <targetfile>
       Verifies the PHY NVM image in eeprom to the target file
       specified in <targetfile>.
    /ADAPTERRESET
       Reset the adapter.
       *CAUTION* This will unload the driver for this device if present.
    /SANMAC_DUMP [/NUM=PF_num]
       Displays the dedicated MAC address for the SAN.
       /NUM is optional and i40e specific - it defines target PF.
    /SANMAC=macaddr [/NUM=PF_num]
       Programs the dedicated SAN MAC address withoutchanging the rest of
       the EEPROM. /NUM is optional and i40e specific - it defines target PF.
    /SANADDRESS <addrfile>
       Programs the dedicated SAN MAC address with the
       MAC address from <addrfile>.
    /INVMVERIFY /FILE=<[path\]filename>]
       Compares autoload configuration stored in OTP memory
       with the configuration defined in configuration file.
    /INVMTEST /FILE=<[path\]filename>]
       Report number of free space left in INVM if autoload configuration
       defined in configuration file would be applied.
Press <Enter> to continue...
    /INVMUPDATE /FILE=<[path\]filename>]
       Write new autoload configuration defined in Raw (*.raw) configuration
       file to empty INVM or updates current autoload configuration stored in
       INVM based on 'human readable' configuration file.
    /INVMISLOCKED
       Checks if autoload configuration stored in OTP
       memory is protected against write attempts.
    /INVMLOCK
       Sets unique record in autoload configuration stored in INVM
       protecting its content against further updates.
    /INVMGET
       Dumps autoload configuration stored in INVM to file
       with predefined name <mac address hex string>.otp.
    /FORCE
       Omits any warnings and forces command execution.
    /KEEPCONFIG
       This option lets you keep config words while upgrading eeprom.
    /PORT_MAC=macaddr /NUM=Port_num
       Programs the dedicated Port MAC address without
       changing the rest of the EEPROM.
    /PORT_MAC_DUMP /NUM=Port_num
       Display the adapter port MAC address.
Press <Enter> to continue...
    /CUSTOM_MAC mac_number mac_addr
       Programs the given custom mac address number [0-3] without
       changing the rest of the NVM (EUI48 and EUI64 formats supported).
    /SERIAL_MAC=macaddr
       Programs the dedicated PCIe serial MAC address without
       changing the rest of the EEPROM.
    /SERIAL_MAC_DUMP
       Display the adapter PCIe serial MAC address.
    /PF_MAC=macaddr /NUM=PF_num
       Programs the dedicated MAC address of a specified Physical Function
       This allows altering the mac addresses of inactive functions of a
       visible NIC.
    /PF_MAC_DUMP /NUM=PF_num
       Display MAC address of a selected Physical Function of the
       specified NIC. This allows dumping MAC addresses of inactive functions
       of a visible device. 
    /MNG_MAC=macaddr /NUM=MNG_num
       Programs the dedicated MAC address of a specified Manageability Function
       This allows altering the mac addresses of inactive functions of a
       visible NIC.
    /MNG_MAC_DUMP /NUM=MNG_num
       Display MAC address of a selected Manageability Function of the
       specified NIC. This allows dumping MAC addresses of inactive functions
       of a visible device. 
    /RO <imagefile>
       Programs RO words in EEPROM/SR with values taken from RO Module binary
       file.

MAC address

If flash BIOS by Intel FPT tool not as fpt -f xxx.bin -savemac. The MAC address for Intel I219 adapter will be missing, and mark as 88-88-88-88-87-88 .

I219-MAC-LOST

Users can use eeupdate to flash the MAC address during DOS/EFI Shell/Windows environment. Command as eeupdate /nic=x /mac=xxxxxx.

eeupdate-flash-i219-mac

If the Computer don’t have Intel adapter, it will prompt others message.

参考资料